Universal 360 °Multi-direction M3-M16 Pneumatic Tapping Tool Air Tapping Drilling Machine. This Pneumatic Tapping Machine All Machinery Industry, Machine Tools, Tooling Machinery, Plastic Machinery, Printing Machinery, Packaging Machinery, Engineering Machinery, Auto And Motorcycle Parts, Aircraft Engines And Other General Purpose Machinery Industries. The Tapping Range is: M3 To M16. Universal (multi-directional, every angle of tapping).Tapping For Copper, Iron, Aluminum, Steel, Stainless Steel, Plastic And Wood, and Other Materials. Tap The Scope From M3 To M16. Re-Positioning Fast, Machining Speed, High Accuracy Wire, and Increased Production Capacity. Extraordinary Load Operation And Will Not Damage Main Motor.
Pneumatic Tools, Torque, Light Weight, High Efficiency. Working area: In Radius 1000mm Max. Tapping Range: M3 to M16.
1, the new patent products, compressed air drive, safe and fast and efficient. 2, the mean pressure and volume (5-8 kg / cm2), large torque. 3, can seal all kinds of steel, iron, copper, aluminum, plastic materials such as tapping. It is not easily broken wires. 4, bus with overload protection, side attack damage is less, the teeth of high precision.5, the operation is simple: hand motor, alignment hole, hold the start button and start tapping, tap in the desired depth, hold the exit, tap head stop automatically, complete a tapping operations. 7, the heavier work content does not require positioning device or mobile, suit with universal head are easily done. 8, quick positioning rapid and high cutting speed, increase production. 9, through hole or blind hole, side attack are not peculiar to breakage, pneumatic tapping machine safety torsion clamp cylinder to tap when encountered in the tapping blind holes. Automatic sliding doors, protect the tap head, high precision tap to tap the high precision. Repeat positioning rapid, can continuously tapping operations on a workpiece, removes old tapping machine every tapping, adjusting the workpiece position for the inconvenience. Wider range of work activities, universal head, can guarantee against spiral Angle. For your use of the safety, read manual, and used in accordance with the safety instructions to operate this machine, to avoid accidental damage due to misuse. When used well, please placed in the location of the smooth, not placed in high places, to avoid degradation the function of the parts.
Rubber base is placed on the corrosive chemicals, not to the machine of the firm. A good job every clean, so as to ensure the life of mechanical, especially two grinding hole is the most important, if not clean, indeed, the parts can wear, and affect the grinding accuracy. One, adjust the vertical: 1, let the pneumatic motor at the bottom of the quick change connectors and work desktop or workpiece plane contact, quick change connectors and work desktop, vertical (quick change connectors with work desktop without clearance), then lock vertical plate or universal head of four locking screw. 2, the air pipe joint in the joint between the engine. Second, the pneumatic motor operation 1, press the front-end pneumatic motor, motor is turned "trigger" of the; The tapping simultaneously the back-end "reverse button" of the pneumatic motor reversal; To exit.
2, parallel arm allows easy tapping position, force a downward, tap it, such as guide screw in and out of the screw hole with very little resistance. Three, air requirements: 1, the inlet section must be 3/8 inch or more than 10mm, length must not exceed 10 m. 2, set the pressure in the 4-8 kg. 3, adjusting air sanlian pieces of drip speed for 3-5 drops per minute, if drip fast motor upper only gets wet from the exhaust oil too much. 4, check the oil in the cup daily, oily and drip speed.5, use pneumatic tools for oil (viscosity 30 or so); Recommendation: sewing machine lubricating oil, light oil. Frequently give air compressor drainage. Air compressor machine often drainage, if air compressor water too much and not discharged in time, will bring pneumatic motor, is long, the bearing is not flexible. 1 x Neumatic Tapping Machine Kit. The item "Universal M3 to M16 Pneumatic Tapping Tool 360 ° Air Tapping Drilling Machine" is in sale since Sunday, June 16, 2019. This item is in the category "Business, Office & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Other Metalworking Equipment". The seller is "hksunwin" and is located in Shenzhen. This item can be shipped worldwide.